Would You Like a Free Expert Consultation?

Las Vegas Handyman 

Not every project goes as well as planned. We would be happy to spend a few minutes answering your questions.

Subscribe by Email

Your email:

Browse by Tag

Pro Handyman Blog

Current Articles | RSS Feed RSS Feed

Garbage Disposal Repair


garbage disposal repairAhh, the fragrant stomach-curdling smell of old food. You know, the kind that looks like a science experiment, except this isn't in a petri dish... it's in your garbage disposal. Coincidently, the garbage disposal isn't working.

At least half the calls I get for broken garbage disposals turn out to be easy fixes.

If the disposal doesn't make noise when you turn it on, press the reset button on the bottom of it. If the motor overheats or is overloaded, this button will trip and turn the motor off. Pressing the button back in will re-start the motor (you should also test the outlet to make sure there is power getting to the disposal and, if not, check the breaker).

If the disposal makes a humming noise, but doesn't grind food, it is jammed. Most disposals come with a tool to clear a jam. If you have lost yours, you can use an Allen wrench. Take the tool and insert it in the hole at the bottom of the disposal (near where the cord enters underneath). As you twist the tool, you will hear and feel the obstruction. Keep twisting until the blades move freely. If you still can't budge the blades, you'll need to remove the disposal and manually clean out the obstacle.

If your disposal is dead, plan on spending about $85 for a 1/2-horsepower disposal, and about an hour to replace it. You can save yourself some time if you buy the same brand of disposal, since the new one will attach easily to the old mounting ring.

To remove the disposal, unplug it and grab a screwdriver. You'll need to disconnect the dishwasher drain hose, which is attached with a hose clamp, and the drainpipe. They should easily disconnect, but have a rag handy to absorb a little water.

The only thing left holding the disposal in place is the mounting ring. The mounting ring squeezes a rubber gasket (the black thing you see when you look down at the sink) into the mounting assembly, which holds the disposal to the sink. The mounting ring has "ears" on it that hold it to the mounting assembly. It also has round lugs in it that will allow you to remove the disposal.

Stick a screwdriver in one of the mounting ears and, as you support the disposal, rotate the ring counter- clockwise. The disposal will drop off into your hand.

If you've chosen the same brand disposal, it should re-attach easily to the old mounting assembly. If you are using a different brand, you'll likely have to remove the old assembly and install the new one. Removing the old assembly usually involves unscrewing the mounting screws and removing the snap ring, gasket, mounting and backup rings, and the sink flange. The new mounting hardware will be included in the new disposal package. If you install the new mounting assembly, make sure you use plumber's putty under the sink flange to keep out the water.

Once the mounting assembly is in place, make the electrical connections in the bottom of the disposal (most disposals don't come with electrical cords included, so if the old cord is in good shape, save yourself $8 and re-use it).

You will need to connect the white wires together with a wire nut, then connect the black wires together. Connect the green wire to the grounding screw and replace the cover plate on the bottom of the disposal.

Next, if you have a dishwasher, remove the knockout plug by placing a screwdriver against the plug and tapping it with a hammer.

Hold the disposal against the mounting assembly so that the mounting ears fit into the openings in the assembly. Turn the mounting ring clockwise until the disposal is supported by the assembly, but don't fully tighten it yet. Line up the drainpipe so that it will easily connect to the disposal. If it is too long, cut it to length with a hacksaw. Attach the dishwasher drain hose to the dishwasher nipple on the side of the disposal and tighten the hose clamp.

Finally, lock the disposal into place by inserting a screwdriver in the mounting lug and turning clockwise until the mounting ears bottom out. Plug in the disposal and listen to the sweet sound of food being ground into oblivion.


Currently, there are no comments. Be the first to post one!
Post Comment
Website (optional)

Allowed tags: <a> link, <b> bold, <i> italics